Cross Technologies 2017-14 Bedienerhandbuch

Instruction Manual Model 2017-14 UHF, L-Band, Up/DownconverterJanuary 2013, Rev. 0MENUEXECUTEMODEL 2017CROSS TECHNOLOG

2.0 Installation2.1 MechanicalThe 2017-14 consists of one RF/Controller PCB housed in a 1 RU (1 3/4 inch high) by 16 inch deep chassis. A switching,

2.2 Rear Panel Input/Output Signals and Control - Figure 2.2 shows the input and output connectors on the rear panel.ACGNDJ18J2RF IN 10 MHZ REFOUTPUT

Tables 2.1 & 2.2 shows the input and output connectors on the rear panel.TABLE 2.1 JJ10 2.1 J10 Pinouts (RS-232C/422/485*)Pin Function1 Rx-2 Rx+ (

2.3 Front Panel Controls and Indicators - The following are the front panel controls and indicators.MENUEXECUTEU U > L G = 10.0MUTE REMOTEALAR

2.4 Installation / Operation2.4.1 Installing and Operating the 2017-14, Upconverter Section1.) Connect a -40 dBm to -25 dBm signal to IF In, J4 (F

Once the external 10 MHz reference is restored (on J13), the user must again manually (via the front panel LCD or Remote M&C) reselect External Re

2.5 Menu Settings2.5.1 Functions - This section describes operation of the front panel controls. There are three operator switches, the LCD display

2.5.2 Power-On SettingsNOTE: THE LAST STATUS OF A UNIT IS RETAINED EVEN WHEN POWER IS REMOVED. WHEN POWER IS RESTORED, THE UNIT WILL RETURN TO IT&a

2.5.4 Gain ChangesWhen you get to this menu note that the gain changes will be made as you make them but if you do not wish to save the changes you h

2.5.4.2 Downconverter GainTo set the Downconverter gain, first push the Menu/Execute switch to get to the gain setting:Operate the Menu/Execute switc

INSTRUCTION MANUALMODEL 2017-14 UHF, L-Band, Up/Downconverter TABLE OF CONTENTS PAGEWarranty 21.0 General 31.1 Equipment Description 31.2

ON POWER UPNORMAL DISPLAYPUSHING MENU/EXECUTE SEQUENCEREV 1.00U U > L G = 10.0D L > U G = 25.0 INTPUSH BUTTONPower UpNormal Display

CROSS TECHNOLOGIES, INC.6170 Shiloh RoadAlpharetta, Georgia 30005(770) 886-8005FAX (770) 886-7964Toll Free 888-900-5588WEB www.crosstechnologies.com E

MODEL 2017-14 UHF, L-Band, Up/Downconverter1.0 General1.1 Equipment Description The 2017-14 UHF, L-band Up/Downconverter converts 0.2-0.4 GHz to 1.2

2017-14 Manual, Rev. 0 Page 4 01/31/131.2 Technical Characteristics Synthesizer Characteristics NONE, Fixed Freque

1.2 Technical Characteristics continued... ©

1.3 Monitor and Control InterfaceA) Remote serial interfaceProtocol: RS-232C, 9600 baud rate, no parity, 8 data bits, 1 start bit, and 1 stop bit.

B) Status Requests Table 1.1 lists the status requests for the 2017-14 and briefly describes them.* PLEASE NOTE: The two character {aa}(00-31) prefix,

C) Commands Table 1.2 lists the commands for the 2017-14 and briefly describes them. After a command is sent the 2017-14 sends a return “>” indic

1.4 Environmental Use InformationA. Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions located in the u