Cross Technologies 2016-03A Bedienerhandbuch

Instruction Manual Model 2017-03A Up/DownconverterOctober 2013, Rev. HMENUEXECUTEMODEL 2017CROSS TECHNOLOGIES INC.U F=15

2.2 Rear Panel Input/Output Signals and Control - Figure 2.2 shows the input and output connectors on the rear panel.ACGNDJ18J2RF IN10 MHZ REFOUTPUTA

Tables 2.1 & 2.2 shows the input and output connectors on the rear panel.TABLE 2.1 JJ10 2.1 J10 Pinouts (RS-232C/422/485*)Pin Function1 Rx-2 Rx+ (

2.3 Front Panel Controls and Indicators - The following are the front panel controls and indicators.MENUEXECUTEU F=1525 G=+00MUTE REMOTEALARM POW

2.4 Installation / Operation2.4.1 Installing and Operating the 2017-03A, Upconverter Section1.) Connect a -40 dBm to -10 dBm signal to IF In, J4 (F

AC Fuse - 2 amp slow blow (Type T), 5 mm X 20 mmFUSE DRAWERSPARE FUSE~INPUT100-240± 10%VAC47-63 Hz2A MAXFUSETYPE T 2A GDC250 VOLTFOR 100 - 240 V~~F

2.5 Menu Settings2.5.1 Functions - This section describes operation of the front panel controls. There are three operator switches, the LCD display

2.5.2 Power-On SettingsNOTE: THE LAST STATUS OF A UNIT IS RETAINED EVEN WHEN POWER IS REMOVED. WHEN POWER IS RESTORED, THE UNIT WILL RETURN TO IT&a

2.5.4 Frequency ChangesAt any time during the modification process, if you have made a mistake and do not wish to save the changes you have made, d

2.5.5 Gain/Level ChangesWhen you get to this menu note that the gain changes will be made as you make them but if you do not wish to save the changes

2.5.5.2 Downconverter GainTo set the downconverter gain, first push the Menu/Execute switch to get to the gain setting:Operate the Menu/Execute switc

INSTRUCTION MANUALMODEL 2017-03A Up/Downconverter TABLE OF CONTENTS PAGEWarranty 21.0 General 31.1 Equipment Description 31.2 Technical Ch

ON POWER UPNORMAL DISPLAYPUSHING MENU/EXECUTE SEQUENCEREV 1.00U F = 1450 G = +00.0D F = 1350 G = +25.0UP F = 1450SCROLL <>SCROLL PUS

CROSS TECHNOLOGIES, INC.6170 Shiloh RoadAlpharetta, Georgia 30005(770) 886-8005FAX (770) 886-7964Toll Free 888-900-5588WEB www.crosstechnologies.com E

MODEL 2017-03A Up/Downconverter1.0 General1.1 Equipment Description The 2017-03A L-band Up/Downconverter converts 70 MHz to 950-1525 MHz (Up) and 95

1.2 Technical CharacteristicsTABLE 1.0 2017-03A Up/Downconverter Specifications*---UPCONVERTER---Input Characteristics (IF)Impedance/Return Loss 7

1.3 Monitor and Control InterfaceA) Remote Serial Interface Protocol: RS-232C, 9600 baud rate, no parity, 8 data bits, 1 start bit, and 1 stop bit.

B) Status Requests Table 1.1 lists the status requests for the 2017-03A and briefly describes them.* PLEASE NOTE: The two character {aa}(00-31) prefix

Table 1.2 lists the commands for the 2017-03A and briefly describes them. After a command is sent the 2017-03A sends a return “>” indicating the co

1.4 Environmental Use InformationA. Elevated operating ambient temperature - if installed in a closed or multi-unit rack assembly, the operating ambi

2.0 Installation2.1 Mechanical - The 2017-03A consists of one RF/Controller PCB housed in a 1 RU (1 3/4 inch high) by 16 inch deep chassis. A switch