Cross Technologies 450T Bedienungsanleitung Seite 15
- Seite / 16
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
15
OPTIONAL FEATURES
OPTIONAL FEATURES
Hydraulic
ES
Hydraulic accumulator for fast injection incl. loading pump and par-
allel ejector movement and core pull movement via double pump
–
–
•
Extra large oil cooler
• •
Core pull movement and parallel ejection with DFEE
double pump
–
–
•
Core pull movement and parallel ejection incl. Fast injec-
tion with DFEE double pump
–
–
•
Injection parallel to clamp force build-up (with hydraulic
accumulator)
–
–
•
Hydraulic core pulls. Limit switch function according to
EUROMAP 13. Pressure and speeds adjustable
• •
Pneumatic core pull
• •
Pneumatic manifold for Mouldmaster nozzle (controlled 1
nozzle or more parallel in the mould)
• •
Hydraulic manifold for Mouldmaster nozzle (controlling 1
nozzle or more parallel in the mould)
• •
Filter in water inlet of oil cooler
• •
Adapter with ball valve on the oil tank for oil maintenance
• •
Separate bypass filtration unit
• •
Clamping unit
Non-standard mould hight after customers request
• •
Isolation platens
• •
T-slots in mould platens
• •
SPI bolt pattern
• •
Ejector cross in clamping platen as per EUROMAP/SPI
• •
Maximum ejector force increased
• •
Mechanical ejector couple
• •
Ejector platen safety device
• •
Mechanical mould safety mechanism
• •
Unscrewing device with hydro-motor additional to standard ejector
• •
Parts chute for separation of good/bad parts
• •
Photoelectric ejection check
• •
Air valve, action initiated (ON) and timer (OFF)
• •
Quick mold clamping system magnet., hydr. or mech.
–
–
•
Injection unit
Grooves in the feeding zone
• •
High torque screw motor in lieu of standard
• •
High temperature heater bands (max. 450° C)
• •
Screw drive by a.c. servo-motor
–
–
•
Ball type screw tip
• •
Needle type shutoff nozzle with spring, pneumatic opera-
ted or hydraulic operated
• •
Melt temperature- or pressure sensor in cylinder head
–
–
•
Hydraulic cross-bolt type shutoff nozzle (from SPE2250)
• •
Open Airmould®-nozzle, pressure controlled
–
–
•
Relief valve for nozzle pressure control (standard from 350t)
• •
Wear resistant screw and barrel AK+
• •
Barrel insulation
• •
Screw with mixing section or barrier section
• •
Hoppermagnet
• •
Hopper loader UNIFEED A1 (till SPE1330)
• •
Safety gate
Operating safety gate at the rear side
• •
Front side gate safety system for manual part removal
• •
ES
Pneumatic safety gate at the operator side
• •
Initiate next cycle by closing safety gate in semi-auto operation
• •
Safety gate clearance operator side/rear side extended
• •
Safety gate rear side lowered at the top of the upper tiebar
• •
Cooling and conditioning
Additional flow controller with temperature gauges
• •
Shut-off valve for cooling water battery
• •
Blow out valve for cooling water battery
• •
Hosting of cooling circuits on the fixed platen for the moving platen
• •
Electrical components
Temperature control zone for hot runner
• •
Non-contact stroke transducers (standard from 350t)
–
–
•
Special voltage
• •
Control cabinet cooler
• •
Closed loop temperature control of mould
• •
Additional socket
• •
Fuse protection for sockets
• •
Power factor correction and active power optimization
–
–
•
Interface for handling equipment
• •
Energy consumption analysis
–
–
•
Integrated Tandemmould
–
–
•
Switch over to holding pressure by cavity or melt pressure
• •
Switch over to holding pressure by external signal
• •
Purging program through the open mold
• •
Melt cushion control
–
–
•
Audible alarm
• •
Analog temperature control interface
• •
Temperature control interface digital, serial 20mA TTY protocol
–
–
•
CAN-Bus-interface for mold conditioner as per EUROMAP 66-2
–
–
•
CAN-Bus-interface for hot runner as per EUROMAP 66-2
–
–
•
Interface for Airmould® mobile/integrated as well as
EUROMAP 62
–
–
•
Interface for robots as per EUROMAP 67
• •
Adaptor from EUROMAP 67 to EUROMAP 12
• •
Interface for conveyor belt
• •
Scale interface
• •
Host computer interface/PDA (EUROMAP 63)
–
–
•
Relays contact parallel to plasticizing
• •
Machine fault (potential-free contact)
• •
BNC connectors for injection process analysis
–
–
•
Remote diagnostics via network
• •
Interface for common data storage with Battenfeld robot
–
–
•
Interface for vacuum pump
–
–
•
Second injection data setting for automatic start up
–
–
•
Accessories
Special paint
• •
Tool kit
• •
Touch-up paint
• •
Levelling pads
• •
USB stick for data storage
• •
Verwandte Produkte und Handbücher für Empfänger Cross Technologies 450T
(13 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern