Cross Technologies 2015-24 Bedienerhandbuch

Instruction Manual Model 2015-24 Upconverter March 2010 Rev C MENUEXECUTEMODEL 2015CROSS TECHNOLOGIES INC.F=1525.000G=

2.2 Rear Panel Input / Output Signals Figure 2.2 shows the input and output connectors on the rear panel.ACGNDJ1810 MHZ REFOUTPUTAC1 - POWER INAC in

2.3 Front Panel Controls and Indicators Figure 2.3 shows the front panel controls and indicators.LCD DISPLAYDisplay shows frequency in MHz and Gain i

FUSE DRAWERSPARE FUSE DRAWERAC Fuse - 2 amp slow blow (Type T 2A GDC), 5 mm X 20 mm~INPUT100-240± 10%VAC47-63 Hz2A MAXFUSETYPE T 2A GDC250 VOLTFOR

2.5 Menu Settings2.5.1 Functions - This section describes operation of the front panel controls. There are three operator switches, the LCD display

2.5.2. Power On SettingsNOTE: The last status of a unit is retained even when power is removed. When power is restored, the unit will return to it&

2.5.4 Frequency ChangesAt any time during the modification process, if you have made a mistake and do not wish to save the changes you have made, d

2.5.5 Gain ChangesWhen you get to this menu note that the gain changes will be made as you make them but if you do not wish to save the changes you h

2.5.5 Alarm IndicationsAn alarm condition for will occur if the local oscillator phase lock loop (PLL) comes out of lock. The Mute LED will light if

2.6 Available Options (Models: 2015-XX, 2016-XX & 2017-XX) Option P48 – ±48 VDC Power Supply, for 2015, 2016 & 2017 Frequency Converters;

Option PWR - Provides +15 dB Output @ 1dB Compression for 2015-XX L-band Upconverter 50 Ohm Connectors ONLY. 2015-XX 2016-XX PWR Redundant Power Su

INSTRUCTION MANUALMODEL 2015-24 Upconverter TABLE OF CONTENTS PAGEWarranty 21.0 General 31.1 Equipment Description

Front Panel Disable for Series 2015/2016 & 2017-XX Frequency Converters. Provides the ability to Disable the Front Panel Interface via the Remot

CROSS TECHNOLOGIES, INC.6170 Shiloh RoadAlpharetta, Georgia 30005(770) 886-8005FAX (770) 886-7964Toll Free 888-900-5588WEB www.crosstechnologies.com E

MODEL 2015-24 Upconverter1.0 General1.1 Equipment DescriptionThe 2015-24 L-band Upconverter converts 140 ± 36 MHz to 950 to 2150 MHz in 1kHz, 10kHz,

1.2 Technical CharacteristicsTABLE 1.1 2015-24 Upconverter Specifications*Input Characteristics (IF)Impedance 75 Return Loss 18 dBFrequency 140

1.3 Monitor and Control InterfaceA) Remote Serial InterfaceProtocol - RS-485, RS-422 or RS-232C (selectable), 9600 baud rate, no parity, 8 data bits,

B) Status RequestsTable 1.2 lists the status requests for the 2015-24 and briefly describes them.* PLEASE NOTE: The two character {aa}(00-31) prefix,

C) Commands Table 1.3 lists the commands for the 2015-24 and briefly describes them. After a command is sent the 2015-24 sends a return “>” indica

1.4 Environmental Use InformationA. Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions located in the u

2.0 Installation2.1 Mechanical The 2015-24 consists of one RF/Controller PCB which is housed in a 1 RU (1 3/4 inch high) by 16 inch deep chassis. A